彩色透明微晶玻璃的吸收光谱

在Li2O-Al2O3-SiO2系统玻璃中掺入少量晶核剂TiO2,ZrO2,P2O5，再掺入稀土离子和过渡金属离子作为着色剂，在高温下溶制得到彩色透明玻璃，对上述玻璃进行微晶化处理，用差热分析（DTA）确定其晶化温度，测定与讨论了所获彩色透明微晶玻璃在紫外波段至近红外波段的吸收光谱特性，研究结果表明，玻璃微晶化后，由于基质玻璃对光的微弱散射，引起吸收的增强，但不改变稀土离子和过渡金属离子的本征吸收峰位。     

Optical current transducers using flint glass fiber as the faraday sensor element

This paper describes development of the optical current transducers using flint glass fiber as the Faraday effect sensing element. Excellent polarization properties of the fiber with low birefringence are described, and the design and test data of a current transducer using the fiber manufactured for use in electric power facilities are reviewed. Experimental results on flexible characteristics of a scheme with round trip light transmission in the fiber is also reported.     

Physical aging of a polyetherimide: Creep and DSC measurements

Creep and differential scanning calorimetry (DSC) measurements have been used to study the physical aging behavior of a polyetherimide. Isothermal aging temperatures ranged from 160°C to T_g with aging times ranging from 10 min to 8 days. The only measurable effect of physical aging on the short-time creep curves is a shift of the creep compliance to longer times. Andrade plots of the compliance versus the cube root of time are linear at short times with the slope β decreasing with increasing aging time to a constant value once equilibrium is reached. Log β³ is related directly to the degree to which the creep curves shift to longer times with physical aging, and is used in this work as a measure of physical aging. A reduced curve of log β³ versus log aging time is obtained for the aging temperatures investigated by appropriate vertical and horizontal shifts. The enthalpy change during aging increases linearly with the logarithm of the aging time, t_a, leveling off at equilibrium at values which increase with decreasing aging temperature. Hence, both nonequilibrium and equilibrium temperature shift factors can be calculated from the DSC data. Good agreement is observed between the equilibrium temperature shift factors obtained from the creep and DSC data. The temperature dependence of the nonequilibrium temperature shift factors is found to be an order of magnitude smaller than that of the equilibrium shift factors. The time scales to reach equilibrium for enthalpy and for mechanical measurements are found to be the same within experimental error. © 1995 John Wiley & Sons, Inc.     

Elevation of the glass transition temperature in flexible‐chain semicrystalline polymers

In the idealized two‐phase model of a semicrystalline polymer, the amorphous intercrystalline layers are considered to have the same properties as the fully‐amorphous polymer. In reality, these thin intercrystalline layers can be substantially influenced by the presence of the crystals, as individual polymer molecules traverse both crystalline and amorphous phases. In polymers with rigid backbone units, such as poly(etheretherketone), PEEK, previous work has shown this coupling to be particularly severe; the glass transition temperature (T_g) can be elevated by tens of degrees celsius, with the magnitude of the elevation correlating directly with the thinness of the amorphous layer. However, this connection has not been explored for flexible‐chain polymers, such as those formed from vinyl‐type monomers. Here, we examine T_g in both isotactic polystyrene (iPS) and syndiotactic polystyrene (sPS), crystallized under conditions that produce a range of amorphous layer thicknesses. T_g is indeed shown to be elevated relative to fully‐amorphous iPS and sPS, by an amount that correlates with the thinness of the amorphous layer; the magnitude of the effect is severalfold less than that in PEEK, consistent with the minimum lengths of polymer chain required to make a fold in the different cases. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1198–1204, 2007     

Thermal transformations of selected transition metals oxyhydroxides

We investigated the features of the glass transition relaxation of two room temperature ionic liquids using DSC. An important observation was that the heat capacity jump, that is the signature of the glass transition relaxation, shows a particularly strong value in this type of new and promising materials, candidates for a range of applications. This suggests a high degree of molecular mobility in the supercooled liquid state. The study of the influence of the heating rate on the temperature location of the glass transition signal, allowed the determination of the activation energy at the glass transition temperature, and the calculation of the fragility index of these two ionic glass-formers. It was concluded that this kind of materials belong to the class of relatively strong glass-forming systems. This revised version was published online in July 2006 with corrections to the Cover Date.     

Sol-Gel Particulate Float Process to Make Vitreous Silica Bodies

Particulate sol-gel technology uses larger particles than that of alkoxide-derived gels and provides larger pore sizes in the gelled object. This allows relatively rapid drying and fabrication of large rods or tubular shapes. However, the formation of more complex or flat shapes, which require extensive surface contact with a mold, is more difficult. The shrinkage during drying, with the significantly greater stress of surface friction due to adhesion, frequently leads to cracking.We have demonstrated a solution to this problem by floating the gel on the surface of a dense liquid. Dry silica panels up to 28 × 40 × 0.7 cm³ were prepared in this way. The use of patterning molds allowed the fabrication of more sophisticated shapes. These bodies were sintered to transparent vitreous silica articles of near net dimensions.     

Molecular modeling study on surface,thermal, mechanical and gas diffusion properties of chitosan

The motivation of this work is to provide reliable and accurate modeling studies of the physical (surface, thermal, mechanical and gas diffusion) properties of chitosan (CS) polymer. Our computational efforts have been devoted to make a comparison of the structural bulk properties of CS with similar type of polymers such as chitin and cellulose through cohesive energy density, solubility parameter, hydrogen bonding, and free volume distribution calculations. Atomistic modeling on CS polymer using molecular mechanics (MM) and molecular dynamics (MD) simulations has been carried out in three dimensionally periodic and effective two dimensionally periodic condensed phases. From the equilibrated structures, surface energies were computed. The equilibrium structure of the films shows an interior region of mass density close to the value in the bulk state. Various components of energetic interactions have been examined in detail to acquire a better insight into the interactions between bulk structure and the film surface. MD simulation (NPT ensemble) has also been used to obtain polymer specific volume as a function of temperature. It is demonstrated that these V–T curves can be used to locate the volumetric glass transition temperature (T_g) reliably. The mechanical properties of CS have been obtained using the strain deformation method. Diffusion coefficients of O₂, N₂, and CO₂ gas molecules at 300 K in CS have been estimated. The calculated properties of CS are comparable with the experimental values reported in the literature. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1260–1270, 2007     

Effect of nanotube functionalization on the properties of single‐walled carbon nanotube/polyurethane composites

A commercially available aliphatic thermoplastic polyurethane formulated with a methylene bis(cyclohexyl) diisocyanate hard segment and a poly(tetramethylene oxide) soft segment and chain‐extended with 1,4‐butanediol was dissolved in dimethylformamide and mixed with dispersed single‐walled carbon nanotubes. The properties of composites made with unfunctionalized nanotubes were compared with the properties of composites made with nanotubes functionalized to contain hydroxyl groups. Functionalization almost eliminated the conductivity of the tubes according to the conductivity of the composites above the percolation threshold. In most cases, functionalized and unfunctionalized tubes yielded composites with statistically identical mechanical properties. However, composites made with functionalized tubes did have a slightly higher modulus in the rubbery plateau region at higher nanotube fractions. Small‐angle X‐ray scattering patterns indicated that the dispersion reached a plateau in the unfunctionalized composites that was consistent with the plateau in the rubbery plateau region. The room‐temperature modulus and tensile strength increase was proportionally higher than almost all increases seen previously in thermoplastic polyurethanes; however, the increase was still an order of magnitude below what has been reported for the best nanotube–polymer systems. Nanotube addition increased the hard‐segment glass transition temperature slightly, whereas the soft‐segment glass transition was so diffuse that no conclusions could be drawn. Unfunctionalized tubes suppressed the crystallization of the hard segment; whereas functionalized tubes had no effect. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 490–501, 2007     

Thickness dependence of free‐standing thin films

Below a critical thickness, of about 60 nm, the glass transition temperature of polystyrene (PS) films decreases with film thickness, as demonstrated using free‐standing films. A geometrical model is developed here describing this phenomenon in the case of ideal (Gaussian) chains. This model, which can be considered as an application of the free volume model, assumes that the decrease of the glass transition temperature from thick to ultrathin films is due to the modification of the interpenetration between neighboring chains. The theoretical curve deduced from the model is in excellent agreement with the PS experimental results, without using any adjustable parameters. From these results, it can be concluded that new chain motions, usually buried in bulk samples, are expressed by the presence of the surface. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 10–17, 2007